Reducing the throttling to this value created a regression with
bringing up RSL on the nanoBTS 900. We do seem to have a bug/issue
in the bsc_init code and might send a command too early without this
longer wait period and then the state transition does not happen.
For now it is agreed that reverting is the best thing to do.
Debugged-by: Sylvain Munaut <246tnt@gmail.com>
This reverts commit f5284ae1cf.
The current code was overly complex. It tried to iterate over
the list in a round robin and we had to keep track of the last
element, see if we remove that one, check if the list becomes
empty... This can all replaced by treating the double linked
list as a queue. We take the item at the front, do something
on it and then and then put it back to the list at the end.
It was possible that the nat detected the core network
gateway as the bts just due being the first to send data
to the port. Fix it by setting a dummy bts_ip to force
the mgcp_network code to compare the in_addr.
On the nanoBTS we do not receive any load indication for the
paging channel and we just decrement our available slots and
the unsigned int wraps to the maximum value. Together with a
not yet understood bug this makes us go amock.
For the nanoBTS and even the Siemens BS11 resetting the load
to 20 after two seconds should be just fine. For the nanoBTS
we would need to reset the 20 a lot more earlier but we need
to take a look at how often we run low.
Set the state to activation to avoid a warning about the
getting a CHAN ACK without waiting for it. We set it in
the code to make sure it is set after all error checking
to avoid inconsistent state as the state is only set back
to NONE/ACT due replies from the BTS.
1.) free every SAPI from 1-7 and wait for the confirmation
and then continue until all of them are freed. If the
SAPI is not torn down we will receive a timeout and then
we force the RF Channel Release...
2.) once SAPI is down we send the RR Release, SACCH Deact
3.) the abis_rsl will see that all SAPIs are down and then
will release channel...
Currently our GSM04.11 code is closing the link for SAPI=3
and this would mean that the whole channel would be scheduled
for close... where we only want to close everything when freeing
the lchan or handling an error.
When we issue a RF Channel Release in case of a failure we receive
RLL release indications after the channel was tearn down and we
issue another RF Channel Release as a result. The channel allocator
might have already allocated this channel and we release the channel
again with another MS on it.
Make rsl_rf_chan_release take an error argument and make it set
a new state in case of an error and change the RF Channel Release
ack to not set the state back to none in case of an error but wait
for a timeout that is a bit higher than T3111.
I tested this with removing the battery during a phonecall and
waiting for the channel failure. With this test we only send the
release once.
We assume that the lchan_free will initiate the release and
that when we handle the RLL release indication or the release
request as part of the shutdown sequence.
The current channel release has a couple of issues we will
need to fix in a set of upcoming commits.
The issues include:
1.) sending release twice
2.) reassigning the channel inbetween the relase..
We need to simulate OML/RSL failure in an easy and fast way
and adding a command to do so seems like a good way to achieve
this. The command is a bit misplaced, in one way it is no config
and does not belong into the config node but then again it does
not belong into the VIEW_NODE either as it is manipulating content.
The refcount should drop to zero immediately and then the
msc_data would be reset automatically but it is better to
remove all traces of it right away.
We will handle sending the assignment failure inside the T10
timer but it is better to reset the secondary_lchan inside the
msc_data right away before we might accidently use it.
1.) when we do get a assignment failure from the MS. It is coming
on the old channel and not the new one. Fix the comparison. Also
always reset the msc_data to NULL before dropping the reference
2.) the LCHAN signal handler in bssap.c claims that the T10 expire
cb should free the secondary channel. It currently does not do
it and we have to do it now...
the whole thing was not tested and even after this commit this
behavior is not heavily excercised... with OsmocoreBB we would be
able to do this in the future.
It appears to be possible that we attempt to submit a DTAP
on a SCCP connection when we have a channel without the msc_data
assigned. This change should fix the crash (which is not well
understood), fix a memleak in the case of the queue being full.
data_len is wrong as well as we have reserved... specifying
it directly seems to make valgrind happy. This also means that
we might receive more than one UDP message and do not properly
forward things. I will need to investigate.
This method currently prepends the IPA header and sends
the data. In the future we might be able to use SCTP for
it.
We have to remove the IPA header from the static messages
for that to work.
This code is untested.
